Proficient Audio Systems M4 User Manual download pdf

1514

M4 QUICK START GUIDE

M4 SPECIFICATIONS

For technical inquiries, please call 877.888.9004 or email us at

techsupport@proficientaudio.com. We are available to assist you every

weekday, except holidays, between the hours of 7:00 a.m. and 5:00 p.m. PST.

940 Columbia Avenue, Riverside, CA 92507

877.888.9004 • Fax 951.787.8747 • proficientaudio.com

Audio Sections

Rated Power/Channel 30 Watts, 20Hz - 20kHz

(RMS, 2 channels driven into 8 Ω)

THD (at rated power) < 0.7%

Power/Channel 45 Watts @ 1kHz

(RMS, 2 channels driven into 4 Ω)

Input Sensitivity 300 mV

(For rated power @ max VC)

Input Impedance (source inputs) > 22 k

Input Overload (source inputs) 2.5 V

Output Voltage @ Pre-Outs 1.7 V, VC Setting, VC Max

(w/300 mV @ source inputs) 810 mV, NVC Setting

Output Impedance (pre-outs) < 300 

Frequency Response (@ 1 watt @ 8 Ω) 20Hz - 20kHz ± 1.5dB

Channel Separation > 50dB @ 10kHz

Crosstalk Between Sources > 65dB @ 10kHz

S/N Ratio (re: rated output, > 95dB (VC 20dB IEC A,

source inputs shorted)

below FCW)

Bass Control Range ±10dB @ 100Hz

Treble Control Range ±10dB @ 10kHz

Control Sections

Contact Closures (dry) 2A, 30V AC/DC Max

Phone Page In Audio Line Level, > 22 k

– Voltage/Impedance

Doorbell/Status In 1 & 2, 10 mA @ 12V AC/DC

3V - 30V AC or DC

Common IR Out

– HI (high power) 9 V Active High, 82  (110 mA Peak)

– LO (emitter power) 9 V Active High, 670  (13 mA Peak)

Zone IR Outs 9.2 V Active High, 620  (13 mA Peak)

– Voltage/Impedance

Source IR Outs (and loop) 11.5 V Active High, 390  (29 mA Peak)

– Voltage/Impedance

Common Status Out

9.5 V @ 100 mA

(0-12V DC)

General

Power Consumption

No Signal (idle) 50 Watts

At 1/8 Rated Power 110 Watts

(3.75 watts/channel)

Line Ratings (120V AC version) 120V AC, 1.8A

Rear Panel Fuse (120V AC version) T5AL 250V

Line Ratings (230V AC versions) 230V AC, 0.9A

Rear Panel Fuse (230V AC versions) T2.5AL 250V

Dimensions (H x W x D) 5

⁄16" x 17⁄" x 15

⁄2"

148mm x 435mm x 394mm

Weight 20 lbs (9.1 kg)

Limited Two-Year Warranty

Proficient Audio Systems warrants to the original retail purchaser only that this product will

be free from defects in materials and workmanship for a period of two years, provided the

speaker was purchased from a Proficient Audio Systems Authorized Dealer.

Defective products must be shipped, prepaid and insured, together with proof of purchase,

to the Proficient Audio Systems Authorized Dealer from whom they were purchased, or to

Proficient Audio Systems at the address listed on this installation instruction manual. Freight

collect shipments will be refused. It is preferable to ship this product in the original shipping

container to lessen the chance of transit damage. In any case, the risk of loss or damage in transit

is to be borne by the purchaser.

If, upon examination at the Factory or Proficient Audio Systems Authorized Dealer, it is

determined that the unit was defective in materials or workmanship at any time during this

warranty period, Proficient Audio Systems or the Proficient Audio Systems Authorized Dealer

will, at its option, repair or replace this product at no additional charge, except as set forth

below. If this model is no longer available and can not be repaired effectively, Proficient Audio

Systems, at its sole option, may replace the unit with a current model of equal or greater value.

In some cases where a new model is substituted, a modification to the mounting surface may

be required. If mounting surface modification is required, Proficient Audio Systems assumes

no responsibility or liability for such modification. All replaced parts and product become the

property of Proficient Audio Systems. Products replaced or repaired under this Warranty will

be returned to the original retail purchaser, within a reasonable time, freight prepaid.

This Warranty does not include service or parts to repair damage caused by accident, disaster,

misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use, volt-

age inputs in excess of the rated maximum of the unit, or service, repair or modification of the

product which has not been authorized or approved by Proficient Audio Systems. This Warranty

also excludes normal cosmetic deterioration caused by environmental conditions. This warranty

will be void if the Serial Number on the product has been removed, tampered with or defaced.

This Warranty is in lieu of all other expressed warranties. If the product is defective in materials

or workmanship as warranted above, the purchaser’s sole remedy shall be repair or replacement

as provided above. In no event will Proficient Audio Systems be liable for any incidental or con-

sequential damages arising out of the use or inability to use the product, even if Proficient Audio

Systems, or a Proficient Audio Systems Authorized Dealer has been advised of the possibility of

such damages, or for any claim by any other party. Some states do not allow the exclusion or

limitation of consequential damages, so the above limitation and exclusion may not apply.

All implied warranties on the product are limited to the duration of this expressed Warranty.

Some states do not allow limitation on the length of an implied warranty. If the original retail

purchaser resides in such a state, this limitation does not apply.

ZONE STATUS LEDS

LED indicators and labels:

Four blue LEDs indicate

that one or more zones

are currently active.

MASTER POWER SWITCH

When pressed in, the M4

permits zones to be turned

ON and OFF by keypad or

touch panel commands.

BLUE INDICATOR LIGHT

Blue indicates the master

power switch is ON and one

or more zones are active.

Red is OFF.

Keypad RJ45 T568B Standard T568A Standard

12V Pin 2, 7 Orange, White/Brown Green, White/Brown

DATA/IR Pin 4, 5 Blue, White/Blue Blue, White/Blue

GND Pin 1, 8 White/Orange, Brown White/Green, Brown

485A Pin 3 White/Green White/Orange

485B Pin 6 Green Orange

1 2 3 4 5 6 7 8

T568A Standard

1 2 3 4 5 6 7 8

T568B Standard

SPKRS

+ –

–

ZONE 4

L R

PRE-OUT

NVC

KEYPAD

IR OUT

PMKIR

Master Keypad

with IR Receiver

ADDRESS

KEYPAD EXPANSION

Riverside, CA. USA • Made in China

proficientaudio.com

+ RELAY

– RELAY

+12V

DATA

GND

485 A

485 B

Keypad

Connector

Rear View

CAUTION:

Colors shown are based on

T568B RJ45 termination.

SEE CHART BELOW

for T568A and T568B

wiring termination.

Inter-Room

Twisted Pair

CAT5 Cable

1,000' (305m) Max.

Orange

White/Brown

Blue

White/Blue

Brown

White/Orange

White/Green

Use Twisted Pair

for 485A & 485B

Green

Figure 11 Ribbon Cable – PMKIR Right

Figure 12 Ribbon Cable – PMKIR Left

KEYPAD HOOKUP

NOTE: The numeric and function keypads will not

work on their own. They must be connected to a

master keypad using the 3-connector ribbon cable

supplied (included with each model). The cable is

symmetrical so it can be connected with the red

striped side up or down, to best fit the configuration.

Figure 11

shows it connected so that the PMKIR

master keypad will be to the right of the PNK numeric

and PFK function keypads when mounted, whereas

Figure 12

places the PMKIR to the left.

Figure 13 RJA-1.1 Adapter

Figure 14 RJA-1.1 Attached to Keypad and CAT5

Figure 15

Using CAT5 Cable to Connect PMKIR Keypads to M4

Figure 10 Moving and Placing Buttons

Figure 9 Remove Decorator Insert Panel

1. The keypads have a pre-installed set of buttons in

place. These may not match the source and function

arrangements you need or desire. To change them,

release the tabs on each end of the keypad, Figure 8,

and remove the decorator insert panel, exposing the

key buttons, Figure 9.

2. Starting with the Zone 1 PMKIR (master keypad),

and using the extra buttons supplied, if needed,

move and place the source and function buttons in

the arrangement you want. See Figure 10. When you

finish the arrangement, replace the decorator insert

panel over the buttons, being careful to see that the

buttons align correctly with the panel openings.

Press the panel down until the tabs “snap” into place.

3. Repeat these steps for each of the other zone

master keypads. Each zone can have its own unique

configuration… but, it is best to keep them as similar

as possible to simplify programming and operation.

4. In the same way, configure the buttons on the

numeric and function keypads (not included) that

you may chose to use in some zones.

5. Connect all keypads to their assigned zones on

the M4 as shown in Figure 7. Be sure to strip then

connect the various colored CAT5 leads to the correct

terminals on each keypad end. Refer to Figure 15.

CONFIGURE THE KEYPAD BUTTONS

NOTE 1: If you want to use RJ45 connectors for

connecting the CAT5 cable to the keypads, you can do

so by using the Proficient model RJA-1.1 RJ45-to-Wire Pin

Adapters. See Figure 13 and Figure 14. Simply insert the

RJA-1.1 pins into the keypad’s connection terminals and

snap the levers in place. Be sure to orient them correctly

as shown.

Figure 8 Release Tab

1301-72400 (rev1)

Figure 1

M4 Front Panel Features

RS232

PHONE (PAGE IN)

DOORBELL / STATUS IN

CONTROL

PORT

FIRMWARE

UPGRADE

OFF ON

COMMON

IR OUT

STATUS OUT: 0 to +12V

120V 60Hz 1.8A ~

FUSE: T5AL 250V

DATA I/O

CONTACT CLOSURE

EXPANSION PORTS

COMMON

SOURCE 1

LOOP

OUT

LOOP

L R

INPUTS

SOURCE 2

LOOP

OUT

LOOP

L R

INPUTS

SOURCE 3

LOOP

OUT

LOOP

L R

INPUTS

SOURCE 4

LOOP

OUT

LOOP

L R

INPUTS

SOURCE 5

LOOP

OUT

LOOP

L R

INPUTS

SOURCE 6

LOOP

OUT

LOOP

L R

INPUTS

SPKRS

+ –

–

ZONE 4

L R

PRE-OUT

NVC

KEYPAD

IR OUT

Riverside, CA. USA

Made in Taiwan

SPKRS

+ –

–

ZONE 3

L R

PRE-OUT

NVC

KEYPAD

IR OUT

SPKRS

+ –

–

ZONE 2

L R

PRE-OUT

NVC

KEYPAD

IR OUT

SPKRS

+ –

–

ZONE 1

L R

PRE-OUT

NVC

KEYPAD

IR OUT

M4 FEATURES

M4 Multi-Zone Audio Amplifier/Controller

The M4 is a four-zone, six-source Audio Amplifier/Controller. It serves as the

“brains” of the entire keypad system. The M4 provides audio switching for

six sources and 30W/channel audio power amplifiers for four zones. It also

has connection termination facilities for the controlled whole house system.

DOORBELL/STATUS IN 1 & 2 JACKS

These 3.5mm mini phone trigger inputs work in

conjunction with the PHONE PAGE IN jack. When

triggered, the phone inputs can be turned on as

programmed by Proficient Editor. If audio paging is

not required, these 1 & 2 jacks may also be pogrammed

as STATUS inputs for power management of source or

zone components. They accept input levels of 3V to 30V

AC or DC for the trigger ON condition. The voltage level

must drop below 1V AC or DC for the OFF condition.

IR OUT

This 3.5mm mini jack, one for each zone, provides dedicated Zone IR

output initiated from the respective zone inputs. They may control

specific zone components when you want to prevent the control of it

from the other zones.

EXPANSION PORTS

RJ45 jacks provide for connection

of specialized RS485 controlled

products and for looping to

additional M4 controllers for zone

expansion capability.

RS-232 DATA I/O

Communication port.

PHONE PAGE IN JACK

This jack provides input porting for audio feeds from

door mikes or other forms of phone or doorbell

paging. The jack is programmable by Proficient

Editor, to turn on as events, when triggered by the

DOORBELL/STATUS IN Jack.

CONTACT CLOSURE

Provides a single pole dry relay

contact to activate any device that

can be controlled or triggered by a

switch closure. The closure can be

programmed within Proficient Editor

to be activated by keypad presses,

Command Library IR, or within macros

for Momentary, Toggle and Open/

Close Paired operations. Spring-loaded

terminals accept wire sizes from 28 to 14

AWG. Internal relay contacts are rated at

2A/30V AC or DC.

CONTROL PORT & FIRMWARE UPGRADE SWITCH

3.5mm 4-circuit mini phone jack allows several control functions. All keypad

programming is accomplished via this port using Proficient Editor in conjunction

with the mating Transfer Cable. It also accommodates factory firmware updates

in conjunction with the FIRMWARE UPGRADE OFF/ON Switch. Be sure to leave

this switch in the OFF position at all times, except, as instructed within Proficient

Editor, when you are doing a firmware update. Such updates ensure that you can

always have the latest functionality improvements in the field. Another function of

this port is that you can control installed system components with bi-directional

data via touch panels or computers using RS232 protocol.

COMMON IR OUTPUT & HI/LO SWITCH

3.5mm mini phone jack provides a common IR output derived from all of

the zone IR inputs and from keypad initiated IR commands derived from

the internal IR library. High or low IR power output is set by means of the

HI/LO switch

. Set it to the LO setting when driving standard low power

emitters (i.e, Proficient IR single flasher). Set it to the HI position when

driving a high power emitter (i.e, a blaster) for teaching IR commands into

learning remotes. Caution: The HI position will damage or destroy low

power emitters!

COMMON STATUS OUT PORT

This 3.5mm mini phone jack will go high (+12V DC)

when any zone is turned ON and will go LOW (under 1V

DC) when the last zone is turned OFF. The max. output

of this jack is 100 mA at 9.5V DC.

IR OUT JACKS

These 3.5mm mini phone jacks, one for each source, provide

dedicated IR output to specific source components. When a

source is selected on a keypad, IR function commands are

routed directly to that source. This prevents cross-control

interference between two or more sources that have

identical IR commands.

IR LOOP JACKS

These six 3.5mm mini phone jacks, one for each source, are

provided exclusively for zone expansion capability when

using two or more M4 controllers. They permit the

source IR signals from the added zones to be carried to

the source component emitters.

L & R AUDIO IN & LOOP JACKS

These RCA jacks – four for each source – provide audio

signal inputs and buffered loop outputs, for each

source. The buffered outputs can be used to drive local

components or loop the signals to the additional zone

inputs of other M4 controllers when using them for source

expansion.

IEC TYPE AC

Mains receptacle and fuse mates with included AC

power cord. Also houses the rear panel replaceable AC

mains fuse (T5AL 250V for 120V, and T2.5AL 250V for

230V/240V)

L & R PRE-OUT JACKS

These RCA jacks provide line level

audio outputs for driving external

power amplifiers for additional rooms

within zones, where needed.

VCNVC SWITCH

The audio output from the PRE-OUT jacks can

either be controlled by the internal volume

control of the M4 (VC position) or be a fixed

line level output in the no volume control

(NVC position). In either case, the tone control

remains available for room “EQ” settings.

KEYPAD ZONE INPUTS

These RJ45 terminals allow for easy

connection of the inter-room wiring

from keypads in the various rooms.

Normally this is accomplished using

CAT5 cable with home-run lengths of

up to 1000'.

L & R SPEAKERS TERMINALS

These 4-circuit plugable screw-down

terminals accept wire sizes from 14 to

28 AWG. They allow quick connection of

the internal amplifiers to stereo pairs of

speakers in the various zone rooms.

Figure 2

M4 Rear Panel Features

1 2 3 4 5

Summary of Contents

Page 1 - SEE CHART BELOW

161514M4 QUICK START GUIDEM4 SPECIFICATIONSFor technical inquiries, please call 877.888.9004 or email us at [email protected]. We are a

Page 2

161514M4 QUICK START GUIDEM4 SPECIFICATIONSFor technical inquiries, please call 877.888.9004 or email us at [email protected]. We are a

Page 3 - Double Gang Triple Gang

13121110SYSTEM CONNECTIONS AND CONFIGURATION RS232PHONE (PAGE IN)DOORBELL / STATUS IN12CONTROLPORTFIRMWAREUPGRADEOFF ONCOMMONIR OUTLOHISTATUS

Page 4

13121110SYSTEM CONNECTIONS AND CONFIGURATION RS232PHONE (PAGE IN)DOORBELL / STATUS IN12CONTROLPORTFIRMWAREUPGRADEOFF ONCOMMONIR OUTLOHISTATUS

Page 5

161514M4 QUICK START GUIDEM4 SPECIFICATIONSFor technical inquiries, please call 877.888.9004 or email us at [email protected]. We are a

Comments to this Manuals

No comments

Proficient Audio Systems M4 User Manual

Browse online or download User Manual for Musical Equipment Proficient Audio Systems M4. Proficient Audio Systems M4 User's Manual

Summary of Contents

Comments to this Manuals